ElectroBoard
EN
Table of Contents
Documentation
Getting Started
🚀 Quick Start📲 Install as App☁️ Account & Cloud
Editor
🖥️ Panel Editor🎛 Devices & Modules🔗 Protection Hierarchy
Settings
🌐 Network Settings🔌 Cable System
Checks
✅ Automatic Checks📊 Load Calculation
Results
🖨 Export & Print📐 One-Line Diagram🔗 Project Sharing
Tools
🧮 Calculators📋 Panel Templates
AI Assistant
🤖 Electrical Consultant📘 IEC Reference
Additional
📶 Offline Mode🐛 Bug Reporting❓ FAQ

Tools

Panel Templates

When you create a new project you can start from one of 3 ready-made templates. Each template is a panel tidied by hand: the devices sit on the rails, the connections, cables and consumers are set, the wires are routed, and the combs and blank modules are in place. The same panels are shown on the home page. The editor's checks find neither safety errors nor any other findings in the templates.

🏡 House, 3-phase

Parameters: three-phase, TN-C-S, 15 kW

A three-phase panel for a private house: three rails of 15 modules, two RCDs (one for the rooms and kitchen, one for the boiler room and yard), four three-phase combs. The load is distributed across the phases.

Rail 1 — Incomer:

  • Input MCB 32 A (3P, curve C), 6 mm² cable (in conduit, 8 m)
  • 3-phase voltage relay 63 A
  • SPD

Rail 2 — Rooms and kitchen (under an RCD 40 A / 30 mA, type A):

  • Kitchen sockets — 16 A, curve C, 2.5 mm² cable (in wall, 12 m)
  • Dishwasher — 16 A, curve C, 2.5 mm² cable (in wall, 8 m)
  • Study sockets — 16 A, curve C, 2.5 mm² cable (in wall, 14 m)
  • Living-room sockets — 16 A, curve C, 2.5 mm² cable (in wall, 16 m)
  • Oven — 20 A, curve C, 4 mm² cable (in wall, 10 m)
  • Lighting — 10 A, curve B, 1.5 mm² cable (in wall, 28 m)

Rail 3 — Boiler room and yard (under an RCD 40 A / 30 mA, type A):

  • Circulation pump — 10 A, curve C, 1.5 mm² cable (in wall, 7 m)
  • Heating boiler — 10 A, curve C, 1.5 mm² cable (in wall, 7 m)
  • Water heater — 16 A, curve C, 2.5 mm² cable (in wall, 6 m)
  • Irrigation pump — 10 A, curve C, 1.5 mm² cable (underground, 35 m)
  • Terrace sockets — 16 A, curve C, 2.5 mm² cable (underground, 18 m)
  • Outdoor lighting — 10 A, curve B, 1.5 mm² cable (underground, 30 m)
  • Panel service socket — a 16 A socket-outlet on the rail under its own 10 A MCB (curve B)

🏠 Apartment, 1-phase

Parameters: single-phase, TN-C-S, 10 kW

A single-phase apartment panel: two rails of 12 modules, two RCDs (one for the rooms, one for the bathroom and kitchen), three combs. The bedroom sockets are protected by an AFDD — an arc-fault detection device.

Rail 1 — Input and rooms:

  • Input MCB 40 A (2P, curve C), 10 mm² cable (in conduit, 6 m)
  • Voltage relay 63 A
  • SPD
  • "Rooms" RCD 40 A / 30 mA (type A), and under it:
    • Lighting — 10 A, curve B, 1.5 mm² cable (in wall, 25 m)
    • Living-room sockets — 16 A, curve C, 2.5 mm² cable (in wall, 15 m)
    • Bedroom sockets (AFDD) — 16 A, curve C, 2.5 mm² cable (in wall, 14 m)

Rail 2 — Bathroom and kitchen (under the "bathroom and kitchen" RCD 40 A / 30 mA, type A):

  • Bathroom sockets — 16 A, curve C, 2.5 mm² cable (in wall, 9 m)
  • Water heater — 16 A, curve C, 2.5 mm² cable (in wall, 8 m)
  • Kitchen sockets — 16 A, curve C, 2.5 mm² cable (in wall, 12 m)
  • Dishwasher — 16 A, curve C, 2.5 mm² cable (in wall, 7 m)
  • Washing machine — 16 A, curve C, 2.5 mm² cable (in wall, 10 m)
  • Panel service socket — a 16 A socket-outlet on the rail under its own 10 A MCB (curve B)

🏢 Office, 3-phase

Parameters: three-phase, TN-C-S, 25 kW

A three-phase office panel: three rails of 18 modules, a main isolator, two RCDs (one for the sockets, one for climate and lighting), a lighting contactor, four three-phase combs. The load is distributed across the phases.

Rail 1 — Incomer:

  • Input MCB 40 A (3P, curve C), 16 mm² cable (in conduit, 6 m)
  • Main isolator 63 A (3P)
  • SPD

Rail 2 — Sockets (3-phase voltage relay 63 A and an RCD 40 A / 30 mA, type A):

  • Open-space sockets 1 — 16 A, curve C, 2.5 mm² cable (in wall, 28 m)
  • Open-space sockets 2 — 16 A, curve C, 2.5 mm² cable (in wall, 32 m)
  • Open-space sockets 3 — 16 A, curve C, 2.5 mm² cable (in wall, 30 m)
  • Kitchen sockets — 16 A, curve C, 2.5 mm² cable (in wall, 14 m)
  • Coffee machine — 16 A, curve C, 2.5 mm² cable (in wall, 11 m)
  • Kettle and microwave — 16 A, curve C, 2.5 mm² cable (in wall, 12 m)

Rail 3 — Climate and lighting (under an RCD 40 A / 30 mA, type A):

  • Lighting contactor 25 A (3P) — three lighting circuits under it, each 10 A, curve B, 1.5 mm² cable (in wall): corridor (18 m), open-space (35 m), meeting room (22 m)
  • Air conditioners 1, 2, 3 — 16 A, curve C, 2.5 mm² cable (in wall, 22 m, 25 m and 27 m)
  • Panel service socket — a 16 A socket-outlet on the rail under its own 10 A MCB (curve B)

Using a Template

  1. Click New project in the project list (Ctrl+O, or "My projects" in the project pill)
  2. In the Panel templates row, select a template; clicking it again clears the choice
  3. Click Create: the project appears with all devices, combs, cables, and consumers
  4. Adapt it to your needs: add or remove circuits, change ratings, cables, and consumers

💡 The network comes from the template: a selected template sets the network itself (phases, TN-C-S earthing, voltage, frequency), so the network-type buttons in the same form do not affect it. After creation you can change the parameters in the panel settings.

Templates are a starting point, not a final solution. Every installation has its own specifics.